Adding Function Commands to the Node

These functions can be added with dtmf commands.

For example, to add a permanent link on *93{node}, you would use:

93=ilink,13

List of Functions(Edit)

These are added {dmtf}=ilink,{number}

  • 1 - Disconnect specified link
  • 2 - Connect specified link — monitor only
  • 3 - Connect specified link — tranceive
  • 4 - Enter command mode on specified link
  • 5 - System status
  • 6 - Disconnect all links
  • 7 - Last Node to Key Up
  • 8 - Connect specified link — local monitor only
  • 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
  • 10 - Disconnect all RANGER links (except permalinks)
  • 11 - Disconnect a previously permanently connected link
  • 12 - Permanently connect specified link — monitor only
  • 13 - Permanently connect specified link — tranceive
  • 15 - Full system status (all nodes)
  • 16 - Reconnect links disconnected with "disconnect all links"
  • 17 - MDC test (for diag purposes)
  • 18 - Permanently Connect specified link — local monitor only
  • 200 thru 215 - (Send DTMF 0-9,*,#,A-D) (200=0, 201=1, 210=*, etc)

Status commands(Edit)

These are added {dtmf}=status,{number}

  • 1 - Force ID (global)
  • 2 - Give Time of Day (global)
  • 3 - Give software Version (global)
  • 4 - Give GPS location info
  • 5 - Last (dtmf) user
  • 11 - Force ID (local only)
  • 12 - Give Time of Day (local only)

cop commands(Edit)

These are added {dtmf}=cop,{number}(and extra values if needed separated via comma's)

  • 1 - System warm boot
  • 2 - System enable
  • 3 - System disable
  • 4 - Test Tone On/Off
  • 5 - Dump System Variables on Console (debug)
  • 6 - PTT (phone mode only)
  • 7 - Time out timer enable
  • 8 - Time out timer disable
  • 9 - Autopatch enable
  • 10 - Autopatch disable
  • 11 - Link enable
  • 12 - Link disable
  • 13 - Query System State
  • 14 - Change System State
  • 15 - Scheduler Enable
  • 16 - Scheduler Disable
  • 17 - User functions (time, id, etc) enable
  • 18 - User functions (time, id, etc) disable
  • 19 - Select alternate hang timer
  • 20 - Select standard hang timer
  • 21 - Enable Parrot Mode
  • 22 - Disable Parrot Mode
  • 23 - Birdbath (Current Parrot Cleanup/Flush)
  • 24 - Flush all telemetry
  • 25 - Query last node un-keyed
  • 26 - Query all nodes keyed/unkeyed
  • 27 -
  • 28 -
  • 30 -
  • 31 -
  • 32 - Touchtone pad test: command + Digit string + # to playback all digits pressed
  • 33 - Local Telemetry Output Enable
  • 34 - Local Telemetry Output Disable
  • 35 - Local Telemetry Output on Demand
  • 36 - Foreign Link Local Output Path Enable
  • 37 - Foreign Link Local Output Path Disable
  • 38 - Foreign Link Local Output Path Follows Local Telemetry
  • 39 - Foreign Link Local Output Path on Demand
  • 40 - IRLP announce Enable
  • 41 - IRLP announce Disable
  • 42 - Echolink announce node # only
  • 43 - Echolink announce node Callsign only
  • 44 - Echolink announce node # & Callsign
  • 45 - Link Activity timer enable
  • 46 - Link Activity timer disable
  • 47 - Reset "Link Config Changed" Flag
  • 48 - Send Page Tone (Tone specs separated by parenthesis)
  • 49 - Disable incoming connections (control state noice)
  • 50 - Enable incoming connections (control state noicd)
  • 51 - Enable sleep mode
  • 52 - Disable sleep mode
  • 53 - Wake up from sleep
  • 54 - Go to sleep
  • 55 - Parrot Once if parrot mode is disabled
  • 56 - Rx CTCSS Enable
  • 57 - Rx CTCSS Disable
  • 58 - Tx CTCSS On Input only Enable
  • 59 - Tx CTCSS On Input only Disable
  • 60 - Send MDC-1200 Burst (cop,60,type,UnitID,DestID,SubCode)

Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

(SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

DestID and subcode are only specified for the 'C' type message.

UnitID is the local systems UnitID. DestID is the MDC1200 ID of

the radio being called, and the subcodes are as follows:

Subcode '8205' is Voice Selective Call for Spectra ('Call')

Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

Astro-Saber('Call')

Subcode '810D' is Call Alert (like Maxtrac 'CA')

  • 61 - Send Message to USB to control GPIO pins (cop,61,GPIO1=0,GPIO4=1.....)
  • 62 - Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0,GPIO4=1.....)
  • 63 - Send pre-configred APRSTT notification (cop,63,CALL,OVERLAYCHR)
  • 64 - Send pre-configred APRSTT notification, quietly (cop,64,CALL,OVERLAYCHR)
  • 65 - Send POCSAG page (equipped channel types only)

Shell Commands(Edit)

These are added {dtmf}=cmd,{command including path}

For example to run a script called fred.sh, with dtmf *68, it would look like:

68=cmd,/bin/sh {pathtoscript}/fred.sh

Advanced Stuff | Main page

Menu

Article:

Search: